As an Amazon Associate I earn from qualifying purchases.1. Dealikee
Dealikee L298N Motor Drive Controller Board Stepper Motor Control Module Dual H-Bridge with 4pcs DC Motor, Mini Φ67mm Smart Car Tire Wheel and Breadboard DIY Set for Arduino
Dealikee - Motor drive controller: l298n used as the main driver chip. And it comes with 2 x 200mm wires with breadboard-friendly 2. 54mm01" male connectors. It has the strong driving ability, low calorific value and strong anti-interference ability.
Attention: to avoid damage the voltage stabilizing chip of Motor Drive Module, please use an external 5V logic supply when using more than 12V driving voltage.
This is a good diy set for arduino and for raspberry pi based rc car project. Tt motor: the motor is a two-axis motor with a reduction ratio of 1:48, which has strong anti-interference ability.
Smart car wheels: the wheels are made of high-strength plastic and the tires are made of durable black rubber. It not only comes with 4pcs wheels and 4pcs update motors with wires, but also 2pcs motor drive modules and 2pcs 400 Pin Solderless Prototype PCB Breadboard, which are very useful accessories for your project.
| Brand | Dealikee |
| Manufacturer | Dealikee |
| Height | 2 cm (0.79 Inches) |
| Length | 3 cm (1.18 Inches) |
| Width | 4 cm (1.57 Inches) |
| Part Number | 5598522 |
| Model | C-50 |
| Warranty | 90 days |
2. Walfront
DC Motor Speed Controller with Overload Protector 12V 36 V 48V 30A Slow Start Adjustable Speed Board for Permanent Magnet DC Brushed Motor
Walfront - Industrial grade-- industrial grade motor, which features high stability. Locked-rotor protection: capable of limiting large currentmaximum 30A caused by locked rotor, instead of cutting off power. Slow start: slow start function will protect the speed controller and the dc motor from instantaneous large current when power on.
Gains barrier terminal block, which make the wire connection easy to conduct. Upgrade with low-voltage protection10V: if powered by storage battery, this device can protect the battery from damage caused by over discharge.
| Brand | Walfront |
| Manufacturer | Walfront |
| Height | 0 cm (0 Inches) |
| Length | 0 cm (0 Inches) |
| Weight | 0.1 kg (0.22 Pounds) |
| Width | 0 cm (0 Inches) |
| Part Number | SB-122 |
| Model | AK3-AT1-GL-M-X |
3. Walfront
DC PWM Controller 1.8V 3V 5V 6V 12V 2A DC Low Voltage Motor Controller Board Without Potentiometer Switch 1803BW
Walfront - Over-current protection with a 2-amp fuse-fuse will be blown if there is too much current, and can reconnect automatically after fuse cools. Controls the speed of a DC motor through adjusting Pulse-Width-Modulation.
Suitable for very low voltage ranging from 1. 8 to 15v and current no more than 2 amps. The potentiometer is fitted with exterior connection line, but without switch. Easy to install and very good quality.
| Brand | Walfront |
| Manufacturer | Walfront |
| Height | 2 cm (0.79 Inches) |
| Length | 11 cm (4.33 Inches) |
| Weight | 0.02 kg (0.04 Pounds) |
| Width | 8 cm (3.15 Inches) |
| Part Number | Walfrontk9dzpywbr6 |
| Model | Walfrontk9dzpywbr6 |
4. Oumefar
MACH3 5 Axis CNC Motion Controller USB Bypass Board for CNC Stepper Motor
Oumefar - The output port is P17 port. 12-24v wide peripheral voltage input, with anti-reverse connection function. The usb power supply and peripheral power supply are separated to ensure the safety of the computer.
Unidirectional relay output port can control the pin switch. Full support for mACH3 and other computer software supporting parallel port control. All input signals are isolated by optical coupling and can be connected to emergency shutdown, tool adjustment, limit, etc.
| Brand | Oumefar |
| Manufacturer | Oumefar |
| Height | 6 cm (2.36 Inches) |
| Length | 23 cm (9.06 Inches) |
| Weight | 0.34 kg (0.75 Pounds) |
| Width | 12 cm (4.72 Inches) |
| Part Number | Oumefar0u2rb4xasq |
5. Purewords
Purewords GRBL 0.9 or 1.1 Controller Control Board for 3 Axis Stepper Motor, Double Y Axis USB Driver Board for CNC Laser Engraver
Purewords - Designed for 3 axis cnc router 1610; 2418; 3018, managed by Software 09j usb grbl controller. Stepper motor driver: a4988 /support stepper motor: 12V, maximum current of 2A ; recommended within 1.
5a ; support stepper motor 42, 57. . Input voltage: 12-36v; laser output: 12V ; 775 motor output 24V. Laser output 2p/3P supports pwm TTL function. Master chip: atmel 328P arduino nano.
6. RUIZHI
RUIZHI DC 5V-36V 15A 3-Phase Brushless Motor Speed Controller Motor Control Board CW CCW Reversible Switch Motor Driver Control Regulator Module
RUIZHI - 3-phase brushless design: this brushless motor speed Controller is fit for DC brushless 3-Phase motors, and it is support motor CW CCW, you can use it easily. Wide voltage range: this 3-phase brushless motor speed Controller has a wide operation voltage range for wide use, and the range is DC 5-36v, you can use it upon different voltage needs.
Suitable size: this brushless motor controller designed with a small size and elegant appearance for easy and convenient daily use, no worry about the space limitation, you can install it for different purposes.
Easy operation: this dc brushless motor controller is easy to operate, and the speed of the motor can be regulated by the potentiometer, you can adjust it upon your different needs speed, very easy and convenient.
Excellent performance: this motor speed switch features with multi-functions to offer a effective performance, simple and most cost-effective operation, which will be shut down if over current, it has stable performance, and it also adopts with a protective current design, no worry about emergency issues happened.
7. Walfront
DC 5V-36V 15A 3-Phase Brushless Motor Speed Controller Motor Control Board CW CCW Reversible Switch Motor Driver Control Regulator Module
Walfront - Easy operation: this dc brushless motor controller is easy to operate, you can adjust it upon your different needs speed, and the speed of the motor can be regulated by the potentiometer, very easy and convenient. Excellent performance: this motor speed switch features with multi-functions to offer a effective performance, which will be shut down if over current, it has stable performance, simple and most cost-effective operation, and it also adopts with a protective current design, no worry about emergency issues happened.
Suitable size: this brushless motor controller designed with a small size and elegant appearance for easy and convenient daily use, no worry about the space limitation, you can install it for different purposes.
3-phase brushless design: this brushless motor speed Controller is fit for DC brushless 3-Phase motors, and it is support motor CW CCW, you can use it easily. Wide voltage range: this 3-phase brushless motor speed Controller has a wide operation voltage range for wide use, and the range is DC 5-36v, you can use it upon different voltage needs.
| Brand | Walfront |
| Height | 3 cm (1.18 Inches) |
| Length | 8 cm (3.15 Inches) |
| Width | 6 cm (2.36 Inches) |
| Part Number | Walfront |
8. Keenso
Brushless Motor Controller, 5V-36V 350W DC Brushless Motor Board Safe Motor Controller BLDC PWM Driver Board with Cable Control Board Module
Keenso - With radiator-- this brushless motor driver board comes with a radiator, speed controller and forward and reverse switch cables, a complete configuration can bring a better experience. Convenient use-- this bldc pwm driver board can be used directly, wide voltage 5-36V, designed with heat sink, lead wire, control switch, high power 350W, convenient to use.
Practical & safe controller-- This motor controller designed with over-current protection, which can greatly enhance the security.
High performance, working voltage: 5-36V; Maximum current: 16A. Maximum power: 350W; Over current protection: yes.
Fit for dc brushless motor-- this pwm driver board can be fit for dc brushless without hall sensor three-phase motors. Widely applications-- this brush less motor controller features wide voltage high power 350W, three-phase high speed brushless non-inductiveno need Hall controller, PWM signal input, suitable for both small motor and large motor.
| Brand | Keenso |
| Manufacturer | Keenso |
| Height | 0 cm (0 Inches) |
| Length | 0 cm (0 Inches) |
| Width | 0 cm (0 Inches) |
| Part Number | Keensozge21m5nro |
9. Keenso
Adjustable Motor Speed Controller Board Speed Switch Module Variable Voltage Regulator 2000W AC 50-220V 25A Pulse Width Modulator
Keenso - Wide temperature control rangeit can use to such as electric stove, and achieve dimming, lighting dimmer, thermostats, electric iron thermostat, water heater tune thermal, small motor speed, pressure regulator effect.
It can be very convenient adjust the current up to 25A, and solve the over current problem of the heating wire resistance is too small in the case of cooling causing good. More after-sales service--we stand behind all of our them with a 100% product guarantee and promise to give you the best in customer care! If you have any issue about the Adjustable Motor Speed Controller Board, please contact us by e-mail, we will try our best within 24 hours to reply.
High-end configurationthis controller uses novel bi-directional high-power SCR. Adjustment range adjust the motor smooth no noise no vibration, with power indication, wide duty cycle adjustment range. Convenient speed controlthis speed motor controller With wires to connect potentiometer and regulation switch to control the speed, it is convenient to use.
| Brand | Keenso |
| Manufacturer | Keenso |
| Height | 3 cm (1.18 Inches) |
| Length | 12.6 cm (4.96 Inches) |
| Weight | 0.04 kg (0.09 Pounds) |
| Width | 8.5 cm (3.35 Inches) |
| Part Number | Keensotx85uznmws |
10. Walfront
110V AC 4000W SCR Electric Voltage Regulator Dimmer Temperature Controller Motor Speed Controlling Module Board With Cooling Fan, motor speed controller
Walfront - Convenient to use, simply connect input terminals to either live wire or neutral wire110V to 220V and output to load, then rotate knob to control voltage.
Widely used as heat controller on electric stoves, light dimmer on lamps, speed controller on small motors, water heaters, or temperature controller on electric soldering iron, etc.
Voltage regulator. Input voltage: ac 110v to 220v; output voltage varies from 0V to 220V AC; Max Power: 4000Wresistive load. Wide voltage regulating range. The output voltage can be easily adjusted from 0V to 220V. Board size: 85mm x 60mm x 45mm / 3. 34" x 2. 36" x 1. 77".
| Brand | Walfront |
| Manufacturer | WALFRONT |
| Height | 4.5 cm (1.77 Inches) |
| Length | 8.5 cm (3.35 Inches) |
| Weight | 0.1 kg (0.22 Pounds) |
| Width | 6 cm (2.36 Inches) |
| Part Number | Walfront-051601 |
| Model | . |
Dealikee - Motor drive controller: l298n used as the main driver chip. And it comes with 2 x 200mm wires with breadboard-friendly 2. 54mm01" male connectors. It has the strong driving ability, low calorific value and strong anti-interference ability.
Walfront - Industrial grade-- industrial grade motor, which features high stability. Locked-rotor protection: capable of limiting large currentmaximum 30A caused by locked rotor, instead of cutting off power. Slow start: slow start function will protect the speed controller and the dc motor from instantaneous large current when power on. Gains barrier terminal block, which make the wire connection easy to conduct. Upgrade with low-voltage protection10V: if powered by storage battery, this device can protect the battery from damage caused by over discharge.
Walfront - Over-current protection with a 2-amp fuse-fuse will be blown if there is too much current, and can reconnect automatically after fuse cools. Controls the speed of a DC motor through adjusting Pulse-Width-Modulation. Suitable for very low voltage ranging from 1. 8 to 15v and current no more than 2 amps. The potentiometer is fitted with exterior connection line, but without switch. Easy to install and very good quality.
Oumefar - The output port is P17 port. 12-24v wide peripheral voltage input, with anti-reverse connection function. The usb power supply and peripheral power supply are separated to ensure the safety of the computer. Unidirectional relay output port can control the pin switch. Full support for mACH3 and other computer software supporting parallel port control. All input signals are isolated by optical coupling and can be connected to emergency shutdown, tool adjustment, limit, etc.
Purewords - Designed for 3 axis cnc router 1610; 2418; 3018, managed by Software 09j usb grbl controller. Stepper motor driver: a4988 /support stepper motor: 12V, maximum current of 2A ; recommended within 1. 5a ; support stepper motor 42, 57. . Input voltage: 12-36v; laser output: 12V ; 775 motor output 24V. Laser output 2p/3P supports pwm TTL function. Master chip: atmel 328P arduino nano.
RUIZHI - 3-phase brushless design: this brushless motor speed Controller is fit for DC brushless 3-Phase motors, and it is support motor CW CCW, you can use it easily. Wide voltage range: this 3-phase brushless motor speed Controller has a wide operation voltage range for wide use, and the range is DC 5-36v, you can use it upon different voltage needs.
Walfront - Easy operation: this dc brushless motor controller is easy to operate, you can adjust it upon your different needs speed, and the speed of the motor can be regulated by the potentiometer, very easy and convenient. Excellent performance: this motor speed switch features with multi-functions to offer a effective performance, which will be shut down if over current, it has stable performance, simple and most cost-effective operation, and it also adopts with a protective current design, no worry about emergency issues happened.
Keenso - With radiator-- this brushless motor driver board comes with a radiator, speed controller and forward and reverse switch cables, a complete configuration can bring a better experience. Convenient use-- this bldc pwm driver board can be used directly, wide voltage 5-36V, designed with heat sink, lead wire, control switch, high power 350W, convenient to use.
Keenso - Wide temperature control rangeit can use to such as electric stove, and achieve dimming, lighting dimmer, thermostats, electric iron thermostat, water heater tune thermal, small motor speed, pressure regulator effect.
Walfront - Convenient to use, simply connect input terminals to either live wire or neutral wire110V to 220V and output to load, then rotate knob to control voltage.
